PS5 No Signal on TV: HDMI Problems and Fixes

A PS5 no signal message usually appears at the worst moment: friends are over, the controller is charged, the console beeps and lights up, and the TV just says "No signal". Before you assume the console is dead, remember that the PS5 and the TV each have to agree on a cable, an input and a picture format. Any one of those can break the handshake.

Work through the checks below in order. The first few take a minute and solve most cases. The later ones tell you whether the problem is inside the console, which matters a lot in July when storms and voltage spikes are common in Lahore.

Look at the light bar when you press the power button.

• Pulses blue, then turns white: the console has booted. The problem is almost certainly between the PS5 and the screen.
• Pulses blue, then switches off: the console is failing to start properly. That points to a power or hardware issue rather than HDMI.
• No light at all: check the power cable, the socket and any surge protector or stabiliser in between before thinking about the picture.
• Orange: the console is in rest mode. Press the PS button on a connected controller to wake it.

If the light turns white and you hear the startup tone but see nothing, carry on below.

1. Switch the TV input manually. Some TVs don't jump to the active HDMI port. Use the TV remote's Input or Source button and cycle through each HDMI option slowly.
2. Reseat both ends of the cable. Unplug the HDMI cable from the console and the TV, check for bent or dirty connectors, then push both ends in firmly.
3. Try another HDMI port on the TV. TV ports are not always equal. One may be the eARC port for a soundbar, and on some sets only certain ports support higher refresh rates.
4. Remove anything in between. Unplug HDMI switches, splitters, soundbars and capture cards. Connect the PS5 straight to the TV.
5. Use a different cable. A ps5 hdmi cable that has been bent sharply behind a TV stand can fail inside without any visible damage. Use the cable that came in the box or a certified high-speed replacement. Long, thin, unbranded cables are a common cause of flickering and blank screens at higher resolutions.
6. Test the TV with another device. Plug a cable box or laptop into the same port. If that also shows nothing, the TV port is the problem.

If the PS5 works on a different TV, look at the original TV's settings next. Some sets need their enhanced HDMI or input signal mode turned on for the port the PS5 uses. Our PS5 TV settings guide covers that setup in detail.

If the cable and TV are fine, the console may be sending a resolution or format the TV won't accept. PS5 safe mode lets you start the console with basic video settings.

1. Turn the PS5 off fully. Hold the power button until it beeps and the light goes out. Don't use rest mode.
2. Press and hold the power button again. Keep holding after the first beep until you hear the second beep, about seven seconds later.
3. Connect the controller with a USB cable and press the PS button. Safe Mode doesn't work over Bluetooth.
4. Choose Change Video Output, then Change Resolution. The console restarts at a low resolution that almost every TV can show.
5. If you still see nothing, return to Safe Mode and try the HDCP Mode option under Change Video Output. HDCP is the copy-protection handshake between devices, and it sometimes fails through older TVs and receivers.

Once you have a picture, raise the resolution and HDR settings one at a time from the console's Screen and Video settings. That way you'll know which setting your TV doesn't accept.

Sony's support page on Safe Mode options explains every option. Leave Reset PS5 and Reinstall System Software alone unless you understand they can erase your data.

If Safe Mode shows nothing, a known good cable and a known good TV still give a blank screen, and the light bar turns white, the console's HDMI port or the chip behind it is the likely suspect. Look for:

• Pins inside the PS5's HDMI port that look bent, pushed back or blackened.
• A port that feels loose, so the cable droops or wiggles.
• Picture that appears only when you press on the cable.
• A burnt smell or discolouration around the port.

Storms and power cuts are a real risk here. A surge can travel through the TV, cable or wall socket and damage the HDMI circuitry on one or both devices. If the blank screen started straight after lightning, a power trip or the electricity coming back after load-shedding, mention that to the technician. Plug both the TV and the console into proper surge protection afterwards. Our guide to running a PS5 on a UPS during load-shedding explains the options.

A ps5 hdmi port repair means opening the console and soldering a new port, and sometimes replacing the chip that handles the signal. This is not a home job. Opening the PS5 can affect any remaining warranty, so check your coverage first. If the console is still under warranty, read the seller's or manufacturer's terms before letting a repair shop touch it.

When you hand the console to a technician:

• Ask them to test it on a TV in front of you before and after the repair.
• Ask whether they will replace only the port or also the HDMI chip, and why.
• Get the work, the parts used and any repair warranty written on the receipt.
• Keep your user data in mind. A repair shouldn't need your password, and you can sign out of your account before handing it over if the screen allows.

If you're buying a used console, connect it to a TV and look at the HDMI port closely during inspection. A replaced port isn't necessarily a problem, but the seller should tell you about it. Our used PS5 guide lists the other checks to make.

Yes. A low-quality or damaged cable may work at low resolution and fail at higher resolution or with HDR. Try the original cable, or a certified high-speed cable, before suspecting the console.

Changing the video output and HDCP mode doesn't delete anything. The Reset PS5 and Reinstall System Software options can erase data, so read the description of each option before selecting it.

The two TVs may support different resolutions, refresh rates or HDCP versions, or one port may need an enhanced signal mode. Start in Safe Mode at a lower resolution, then increase settings one at a time.

A good repair with a quality port and correct soldering can last for years. If the surge also damaged the chip behind the port, replacing only the port may not hold. Ask the technician what they tested.

If you need a replacement cable or are looking at another console, browse PlayStation cables or PS5 consoles and message MacVault on WhatsApp for current stock and photos of the exact item.